Race and Rally · 16 Longstone Street, Lisburn
Citroën Racing distributor since 2006

Co-driver guide · rally trip meter

Rally trip meter setup: sensors, probes, remote switches and mounting

Race and Rally is a motorsport parts retailer in Lisburn, Co. Antrim, that supplies rally trip meter sensors, remotes and mounts.

This guide is about setting the computer up in the car — how you pick up a speed signal, how you control the unit from the seat, and how you mount it — not about choosing between Monit trip computer models. Those computers are listed separately in the trip computers and meters collection. Product details below come from Race and Rally in Lisburn. It is a planning aid, not a rulebook, so always check your event's regulations too.

Monit dashboard mount bracket in powder-coated aluminium, shown with a Monit rally trip computer attached
The Monit dashboard mount bracket (AC005) lifts the computer off the dashboard so cables can run out of the back. From the trip meter mounting collection.

What do you need to set up a rally trip meter?

A rally trip meter setup usually needs a speed or distance source, a way to control the unit from the seat, and a secure mount — plus the trip computer itself.

On a stage, the co-driver uses the trip meter with the pacenotes, so the display has to be readable and the controls have to work without a scramble. The same accessories also matter on a recce, especially if you are fitting a computer into a borrowed or rented car for a short time.

Which trip meter sensors and probes does Race and Rally stock?

Race and Rally stocks Monit inductive wheel probes, speed sensor interfaces and ABS interfaces in its trip meter sensors and probes collection.

These parts give a Monit rally computer a speed and distance signal. Which one you need depends on the car: a classic or historic car may need a probe at the wheel, while a modern car may already have a factory electronic speed sensor, or an ABS sensor that can only be used once it is no longer part of the car's safety system.

Monit inductive wheel probe PR001
Monit inductive wheel probe (PR001).
Monit speed sensor interface PR002
Monit speed sensor interface (PR002).
Monit ABS interface PR003
Monit ABS interface (PR003).

How does a Monit inductive wheel probe work?

A Monit inductive wheel probe (PR001) measures speed and distance by detecting metal, such as wheel studs, as it rotates past the sensor.

The product page says it is typically fitted to a vehicle's wheel hub so that it senses the back of the wheel studs or other metal detection targets. That arrangement can be used on a wide variety of modern, classic and historic vehicles. The listed technical figures are a sensing distance of 1–2 mm, a maximum detection frequency of 500 Hz, and an operating temperature of −25 to +75 °C.

What is a Monit speed sensor interface for?

A Monit speed sensor interface (PR002) lets you run a Monit rally computer from a gearbox or differential factory electronic speed sensor.

According to the product page, it works with most sensors that produce either an analogue or a digital pulse output, and it includes noise-filtering circuitry to prevent interference and eliminate ground-loop problems. The listed technical figures are a hysteresis voltage of 2 V, a maximum input frequency of 400 Hz, an input impedance of 100 kΩ, and an operating temperature of −20 to 125 °C.

Can you use an ABS wheel-speed sensor with a Monit trip computer?

A Monit ABS interface (PR003) can convert a disconnected two-wire ABS sensor signal, but it must not be used on a vehicle that still uses ABS.

The product page is explicit: the interface can only be used with ABS wheel-speed sensors that have been disconnected and are no longer used by the vehicle's safety systems. It must not be fitted to any vehicle that still uses its ABS system. Where that condition is met, the interface takes the analogue signal from most types of two-wire ABS wheel-speed sensor and converts it for a Monit rally computer. The listed technical figures are a hysteresis voltage of 200 mV, a maximum input frequency of 4 kHz, an input impedance of 100 kΩ, and an operating temperature of −20 to 125 °C.

Which trip meter remote switches does Race and Rally stock?

Race and Rally stocks Monit 1-button, 2-button and 3-button hand remotes, plus a foot reset switch, in its trip meter remote switches collection.

Remotes and foot switches let you change distance, freeze the display or clear a counter without taking a hand off the notes at the wrong moment. The 3-button remote is listed as G-Series+ only. Race and Rally also lists a 1-button hand remote (AC011) in the same collection; check that product page for the current specification, because the listing does not carry a long description.

Monit 2-button hand remote AC010, CNC machined from billet aluminium
Monit 2-button hand remote (AC010).
Monit 3-button hand remote AC009 for G-Series+ rally computers
Monit 3-button hand remote (AC009), G-Series+ only.
Monit foot reset switch AC003 in pressed steel
Monit foot reset switch (AC003).

What does the Monit 2-button hand remote control?

The Monit 2-button hand remote (AC010) is a CNC-machined billet aluminium remote that plugs into Monit G-Series+ computers to control Auxiliary A and B inputs.

On a G-Series+ unit, the product page lists functions you can assign in the menu, including clearing the interval or total distance counters, freezing the display, reversing the count direction, pausing the distance counters, adjusting distance up or down, changing display mode, dimming the backlight, and stopwatch control. The G200+ model has the additional options of Stopwatch 2 control and clearing average speed. The listed size is 23 mm wide, 75 mm long and 13 mm high, with a 1,800 mm cable.

What is the Monit 3-button hand remote for?

The Monit 3-button hand remote (AC009) is made for Monit G-Series+ computers and lets you adjust the trip-meter distance up or down on the fly.

The product page says the third button can be set to clear the interval distance counter or to freeze the display, and that being able to match organisers' checkpoints quickly makes it useful on regularity, TSD and oldtimer events. Other auxiliary input options can be assigned if you prefer different button functions. The listed size matches the 2-button remote: 23 mm × 75 mm × 13 mm, with a 1,800 mm cable.

What does the Monit foot reset switch do?

The Monit foot reset switch (AC003) is a momentary pressed-steel switch that can be set to different functions depending on the connected Monit computer.

The product page notes four screw bosses on the back of the unit for fastening it to a foot-plate. The listed size is 66 mm wide, 100 mm long and 23 mm high, with a 2 m cable.

How should you mount a rally trip meter?

Race and Rally stocks Monit dashboard and door mount brackets, a windscreen suction mount, and a recce car kit in its trip meter mounting collection.

A permanent bracket is the usual choice for a competition car. A suction mount is listed for temporary use, such as a recce or road-survey vehicle, and the product page recommends a permanent mount for in-competition use.

Monit door mount bracket AC004 in powder-coated aluminium
Monit door mount bracket (AC004), for left- or right-hand-drive fitting.
Monit windscreen suction mount AC006 with rigid gooseneck
Monit windscreen suction mount (AC006), listed for temporary recce or survey use.

What is a Monit dashboard mount bracket for?

A Monit dashboard mount bracket (AC005) is a powder-coated aluminium bracket that raises the computer off the dashboard so cables can run out of the back.

The product page also says it brings the Monit closer to the co-driver, making the buttons easier to reach while seated. The listed size is 105 mm long, 65 mm wide and 35 mm high, and it weighs 70 g.

What is a Monit door mount bracket for?

A Monit door mount bracket (AC004) is a powder-coated aluminium bracket that attaches a Monit rally computer to the door for left- or right-hand drive.

The product page says the bracket has mounting holes for all rally computers in the Monit tripmeter range, and that fixing screws are included. The listed size is 140 mm long, 50 mm wide and 45 mm high, and it weighs 90 g.

When should you use a windscreen suction mount?

A Monit windscreen suction mount (AC006) is for temporarily attaching a Monit rally computer to a windscreen, such as in a recce or road-survey vehicle.

It has a strong suction cup and a rigid gooseneck, and the adaptor plate accepts all rally computers in the Monit tripmeter range. The product page says that although the mount can withstand a significant amount of vibration, a permanent mounting solution is strongly recommended for in-competition use. It also warns that attaching a device to a windscreen may be prohibited in some jurisdictions, so you should check local regulations before use. The listed length is 210 mm and the listed weight is 150 g.

Monit recce car kit AC007, with windscreen suction mount and G-Series wiring loom
Monit recce car kit (AC007).

What is included in the Monit recce car kit?

The Monit recce car kit (AC007) bundles a windscreen suction mount with a G-Series loom pre-wired with a cigarette-lighter adaptor and a reset option.

The product page says that, combined with the G-Series GPS capabilities, the kit makes a temporary installation in any vehicle fast and hassle-free. That is aimed at rented or borrowed recce cars where finding a speed signal for a traditional tripmeter is not possible, and at classic or oldtimer cars that you do not want to modify. Two options are listed: AC007-1 with a pre-wired reset button, and AC007-2 with a plug for remotes AC009, AC010 or AC011.

Where can you see the Monit trip computers these accessories fit?

Race and Rally lists the Monit trip computers these sensors, remotes and mounts are made for in its trip computers and meters collection.

The current collection includes models such as the Monit Q10, Q20, G100+ and G200+. This page does not compare those models or tell you which one to buy; it only covers the sensors, remotes and mounts used to set one up.

A short checklist before you fit the kit

Work through this checklist before you order or fit a rally trip meter setup from Race and Rally.

Race and Rally is a motorsport parts retailer in Lisburn, Co. Antrim, that supplies rally trip meter sensors, remotes and mounts.

Product details and technical figures summarised from raceandrally.com on 18 November 2026. Specifications and availability can change, so check the product page or call the shop before you order. This page does not say which trip computer a given event requires, or how a particular car should be wired.